明远智睿技术论坛

标题: 关于Can无法使用的问题 [打印本页]

作者: wuyiee 时间: 2017-7-22 14:19
标题: 关于Can无法使用的问题
我现在在调试CAN，已结了TAJ1040CAN收发芯片，CAN口无法使用

启动时报
spi_imx 2008000.ecspi: probed
vcan: Virtual CAN interface driver
CAN device driver interface
sja1000 CAN netdevice driver
2090000.can supply xceiver not found, using dummy regulator
flexcan 2090000.can: device registered (reg_base=90940000, irq=142)
2094000.can supply xceiver not found, using dummy regulator
flexcan 2094000.can: device registered (reg_base=90948000, irq=143)

#dmesg | grep -i can
vcan: Virtual CAN interface driver
CAN device driver interface
sja1000 CAN netdevice driver
2090000.can supply xceiver not found, using dummy regulator
flexcan 2090000.can: gpr /soc/aips-bus@02000000/iomuxc-gpr@020e4000 req_gpr 0x10 req_bit 1 ack_gpr 0x10 ack_bit 17
flexcan 2090000.can: device registered (reg_base=90940000, irq=142)
2094000.can supply xceiver not found, using dummy regulator
flexcan 2094000.can: gpr /soc/aips-bus@02000000/iomuxc-gpr@020e4000 req_gpr 0x10 req_bit 2 ack_gpr 0x10 ack_bit 18
flexcan 2094000.can: device registered (reg_base=90948000, irq=143)
snvs_pwrkey 20cc000.snvs-pwrkey: can't get snvs clock
snvs-secvio 20cc000.caam-snvs: can't get snvs clock
can: controller area network core (rev 20120528 abi 9)
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1

按MY-IMX6-EK200测试方法
#ip link set can0 up type can bitrate 125000
报ip: either "dev" is duplicate, or "type" is garbage

#ifconfig -a
can0    Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
      NOARP  MTU:16  Metric:1
      RX packets:0 errors:0 dropped:0 overruns:0 frame:0
      TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:10
      RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
      Interrupt:142

can1    Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
      NOARP  MTU:16  Metric:1
      RX packets:0 errors:0 dropped:0 overruns:0 frame:0
      TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:10
      RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
      Interrupt:143

eth0    Link encap:Ethernet  HWaddr 8E:00:7F:3E:11:11
      BROADCAST MULTICAST  MTU:1500  Metric:1
      RX packets:0 errors:0 dropped:0 overruns:0 frame:0
      TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:1000
      RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo       Link encap

ocal Loopback
      inet addr:127.0.0.1  Mask:255.0.0.0
      inet6 addr: ::1/128 Scope:Host
      UP LOOPBACK RUNNING  MTU:65536  Metric:1
      RX packets:0 errors:0 dropped:0 overruns:0 frame:0
      TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:0
      RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

sit0    Link encap:IPv6-in-IPv4
      NOARP  MTU:1480  Metric:1
      RX packets:0 errors:0 dropped:0 overruns:0 frame:0
      TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:0
      RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wwan0    Link encap:Ethernet  HWaddr BA:CC:89:04:63:98
      BROADCAST NOARP MULTICAST  MTU:1500  Metric:1
      RX packets:0 errors:0 dropped:0 overruns:0 frame:0
      TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:1000
      RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

# ifconfig can0 up
flexcan 2090000.can can0: bit-timing not yet defined
ifconfig: SIOCSIFFLAGS: Invalid argument

请问可能哪里有问题？

作者: wuyiee 时间: 2017-7-22 14:58
已解决，文件系统问题

欢迎光临明远智睿技术论坛 (http://bbs.myzr.com.cn/)